Hazardous substances in indoor dust emitted from waste TV recycling facility

Various hazardous substances contained in waste TV sets might be released into environment via dust during recycling activities. Two brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), and tetrabromobisphenol A (TBBPA), and five kinds of heavy metals (Cu, Pb, Cd, Cr, and Ni) were detected in indoor dust collected from two workshops (TV dismantling workshop and subsequent recycling workshop). PBDEs concentrations in dust from waste wires recycling line (722,000 ng/g) were the highest among the studied sites, followed by those in manual dismantling–sorting line (117,000 ng/g), whereas TBBPA concentrations were the highest in manual dismantling–sorting line (557 ng/g) and printed circuit board (PCB) recycling line (428 ng/g). For heavy metals, Cu and Pb were the most enriched metals in all dust samples. The highest concentration of Pb (22,900 mg/kg) was found in TV dismantling workshop-floor dust. Meanwhile, Cu was the predominant metal in dust from the PCB recycling line, especially in dust collected from electrostatic separation area (42,700 mg/kg). Occupational exposure assessment results showed that workers were the most exposed to BDE-209 among the four PBDE congeners (BDE-47, BDE-99, BDE-153, and BDE-209) in both workshops. The hazard quotient (HQ) indicated that noncancerous effects were unlikely for both BFRs and heavy metals (HQ?<?1), and carcinogenic risks for Cd, Cr, and Ni (risk?<?10^?6) on workers in two workshops were relatively low.     

Tree bark as a passive air sampler to indicate atmospheric polybrominated diphenyl ethers (PBDEs) in southeastern China

The different barks were sampled to discuss the influence of the tree species, trunk circumference, and bark thickness on the accumulation processes of polybrominated diphenyl ethers (PBDEs) from air into the bark. The results of different PBDE concentrations indicated that barks with a thickness of 0–3 mm collected from weeping willow, Camphor tree, and Masson pine, the trunk circumferences of which were 100 to 150 cm, were better PBDEs passive samplers. Furthermore, tree bark and the corresponding air samples were collected at Anji (AJ), Hangzhou (HZ), Shanghai (SH), and Wenling (WL) to investigate the relationship between the PBDE concentrations in bark and those in air. In addition, the significant correlation (r ²?=?0.906; P?<?0.05) indicated that atmospheric PBDEs were the principle source for the accumulation of PBDEs in the barks. In this study, the log K _BA (bark–air partition coefficient) of individual PBDE congeners at the four sites were in the range from 5.69 to 6.79. Finally, the total PBDE concentration in WL was 5 to 20 times higher than in the other three cities. The result indicated that crude household workshops contributed a heavy amount of PBDEs pollution to the environment, which had been verified by the spatial distribution of PBDEs levels in barks collected at Wenling (range, 26.53–1317.68 ng/g dw). The good correlation between the PBDE concentrations in the barks and the air samples and the variations of the PBDE concentrations in tree barks collected from different sites reflected that the bark could be used as a passive sampler to indicate the atmospheric PBDEs.     

船舶塑料垃圾热解特性及动力学分析

利用热重分析(TGA)研究船舶塑料垃圾在不同升温速率和不同气氛下的热解特性,并得到了热解动力学参数。结果表明,船舶塑料垃圾的热解过程主要有3个阶段,比一般塑料热解复杂;随着升温速率增大,最大热解速率和最大热解速率温度等热解特性参数也增大,反应变得更剧烈;N2/CO2比为4∶1时,热解反应进行得最完全,固体残留率最少。动力学分析表明,采用3个连续一级反应模型能很好地拟合实验数据;不同的升温速率和气氛比对反应各阶段活化能均有不同程度的影响。     

负载纳米TiO_2凹凸棒黏土的制备表征及对Mn~(2+)的吸附性能

以溶胶-凝胶法制备了负载纳米TiO2凹凸棒黏土吸附剂,采用SEM、XRD等分析方法对负载纳米TiO2凹凸棒黏土前后的结构进行了表征,并对Mn2+进行了吸附性能的研究。结果表明:经过高温焙烧后的负载纳米TiO2凹凸棒黏土吸附剂较负载前的凹凸棒黏土,因其结构中的结晶水和沸石水脱失,内部孔道面积和表面积增加,活性吸附位点的数量增大,吸附能力有了明显提高。在室温条件下(20~25℃),pH为5~6,吸附平衡时间为120 min时,负载纳米TiO2凹凸棒黏土吸附剂对Mn2+有较好的吸附效果。     

优化的甘蔗皮渣吸附居室甲醛

为了研究优化后的甘蔗皮渣吸附居室中的甲醛,本研究通过3种方法处理材料进行吸附甲醛对比,得出简便高效的碱热烫处理,并针对其热烫时间(X1)、pH值(X2)、水浴锅温度(X3)和水浴时间(X4)设置正交实验,得出热烫时间30 min、pH=11、水浴锅温度80℃、水浴时间2.5 h,甘蔗皮渣对甲醛吸附率可达27.91%。通过与活性炭、硅藻纯吸附效果比较,经F检验得出优化处理甘蔗皮渣与硅藻纯吸附效果相当,均极显著优于活性炭。电镜观测出优化甘蔗皮渣与活性炭、硅藻纯同具粗糙、皱褶、疏松多孔结构;傅里叶红外光谱分析出C≡C等基团在甲醛吸附中起主要作用。     

污泥淤砂分离器再分离底流污泥

研究了污泥淤砂分离器对分离原污泥所得的底流污泥进行再分离时,分离分流污泥的性质。实验结果表明,原污泥MLVSS/MLSS为0.372,1次分离后得到的底流污泥MLVSS/MLSS为0.222,2次分离后得到的底流污泥MLVSS/MLSS为0.126,表明通过底流污泥再分离,能够进一步降低底流污泥中生物有机质的含量,提高底流污泥中无机淤砂的含量。同时,原污泥CST为2.85(s·L)/g SS,1次分离后得到的底流污泥CST为0.98(s·L)/g SS,2次分离后得到的底流污泥CST为0.12(s·L)/g SS,表明底流污泥再分离进一步提高了底流污泥的脱水性能,最终得到的底流污泥脱水性能良好。     

煅烧的水滑石同时去除水体中砷和氟

为探讨水滑石类材料对水体中氟、砷离子的同时去除效果,采用共沉淀法合成(Mg∶Al=2∶1)纳米类水滑石(LDHs),用傅立叶转换红外光谱、电子扫描透射电镜、X射线晶体衍射等手段对合成的材料进行了表征,并研究纳米材料在不同初始浓度、pH、吸附时间、阴离子干扰条件下其同时除砷氟性能。结果表明,煅烧后的水滑石(LDOs)对砷最大吸附量为51.02 mg/g,对氟最大吸附量为36.63 mg/g。吸附动力学实验表明,煅烧水滑石对砷的吸附在前6 h内基本完成,对氟的吸附在前10 h内基本完成。砷氟共存溶液保持pH=4~10及pH=6~8时,水滑石分别对砷、氟保持良好的吸附效率。对比不同阴离子对水滑石共除砷氟效率的影响,水滑石除砷速率受到阴离子影响力大小为:HPO2-4CO2-3NO-3Cl-SO2-4;水滑石除氟速率受到阴离子影响力大小为:CO2-3HPO2-4SO2-4Cl-NO-3。材料再生循环利用4次后,对砷和氟的吸附效率均能达到90%以上。实验结果表明,所合成的水滑石是一种优秀的能共除砷氟的吸附剂。     

海口市臭氧污染特征

基于2013—2015年海口市4个空气质量自动监测站点数据,结合气象资料,分析了海口市O_3的污染特征。结果表明:海口市O_3总体优良,优良天数比例为99.4%,污染天数均为轻度污染;在良和污染天数中,O_3作为首要污染物的天数占40%,超过其他5项污染物占比。海口市10月O_3浓度最高。O_3月均浓度与温度呈负相关关系,同时与风向有密切关系:5—8月气温较高,以南风为主,O_3浓度较低;1月北风频率较高,易受外来污染传输作用,O_3浓度相对较高。O_3超标日以东北风为主,日变化并未呈现单峰型特征,12:00—22:00时段O_3浓度在10%范围内小幅变化。台风外围型和北方冷高压底部型是造成海口市O_3超标的2类典型天气形势。     

悬挂链生物接触氧化工艺处理河道污水

采用悬挂链曝气式接触氧化工艺在3个时段内处理城市河道污水,通过采用磷脂法、TTC-脱氢酶活性法和MPN法研究载体表面生物膜特性,来验证装置的水质净化效果。结果表明,进水水质变化幅度较大的时段1内,水质对缺氧区和好氧区内生物膜量及活性有很大冲击,对污染物的去除效果影响不大,COD、NH+4-N、TN和TP的平均去除率分别达到75.9%、80.8%、64.6%和78.3%;进水水质稳定的时段2内,缺氧区和好氧区内生物膜量和活性要高于其他时段,COD、NH+4-N、TN和TP的平均去除率分别达到77.0%、80.6%、69.4%和55.3%;低温运行的时段3内,缺氧区和好氧区内生物膜量和活性都低于其他时段,水质净化效果明显下降,COD、NH+4-N、TN和TP的平均去除率分别为71.1%、68.5%、48.9%和46.6%。     

抗生素与LED209对大肠杆菌的联合毒性机制

抗生素是一把双刃剑,在提高医疗水平的同时会促进抗性基因的发展。群体感应抑制剂(quorum sensing inhibitors,QSIs)可有效地避免这一缺陷,有望成为抗生素的替代品而与抗生素有环境共存的可能,但目前尚缺乏它们的联合毒性机制及其相关的环境风险评价研究。本文以大肠杆菌为受试生物,测定了群体感应抑制剂N-苯基-4-(3-苯基硫代脲基)苯磺酰胺(LED209)与5种抗生素的单一和二元联合毒性。结果表明,LED209与5种抗生素的联合毒性作用均表现为拮抗,推测是LED209通过影响鞭毛合成,减弱了抗生素对大肠杆菌的生物有效性;同时通过拆分分子式,发现了拮抗作用可能源于LED209分子式中的含苯基和硫代脲基的L1分子,因此建议未来在LED209药物优化时,应尽可能的保留L1部分的基团,从而保证混合体系的最小环境风险。本研究不仅为联合用药提供依据,而且从环境风险评价角度为抗生素替代品LED209的结构优化提供理论指导。